Danfoss BD35F Compressor Troubleshooting

Danfoss BD35F variable speed refrigeration compressors are designed for connection to 12V and 24V DC power supply and for refrigerant R134a. These compressors can be used in refrigerators and freezers using either capillary tube or TEV as the throttling device. Danfoss BD compressors especially used in mobile applications such as boats, cooling boxes, caravans, buses, vans, trucks, etc. If you are looking for Danfoss BD35F compressor troubleshooting, read on to this entire blog to repair it easily.

Danfoss BD35F Compressor Troubleshooting

These compressors are also suitable for stationary applications powered by photovoltaic solar panels due to their low energy consumption and wide supply voltage range. Before starting the Danfoss compressor troubleshooting process, we will have a look at a few instructions on the compressor.

The Danfoss BD compressor includes an electronic unit. It has features battery protection, overload protection, fan, LED, and lamp connections, load dump and adaptive energy optimizing. This electronic unit has internal voltage recording and calibration to the applied voltage. It is also powered directly from certain types of electronic power supply units so that no particular battery is required.

Danfoss BD compressors should be mounted in a dry and clean place. They will withstand storage temperatures down to -35°C.

Condensing temperatures:

At stable conditions, maximum 60 degrees C and 70°C at peak load.

Ambient temperatures: Max. 55°C and Min. -10°C.

You should use filter driers which are declared by the Danfoss only in the refrigeration systems with BD compressors. Filter material powder ending up in the compressor will lead to excessive wear of the piston. And, transmission parts deposited in the motor windings will cause the compressor to stop because the electric signal back to the electronic unit is disturbed.

The electronic unit should be mounted on the compressor. It always be connected to the battery poles or power supply unit terminals directly. You should install an external fuse in the power supply cable close to the battery or power supply unit.

If the compressor is to be stopped for a long period, you can install the main switch to avoid the battery from being drained.

Danfoss BD Compressor Troubleshooting

Is your Danfoss compressor stops working? It is recommended to use a LED which is installed between the terminals + and D to determine why your compressor not working.

You should check the electronic unit that is connected properly to the power supply.

Verify if the thermostat is ON.

The number of flashes emitted by the LED will give you a hint about the cause for interruption of compressor operation.

Check the motor windings for defects by measuring the resistance between the current lead-in pins.

If the measured resistance values between all three pins are approximately same, consider that the motor is most likely all right.

Here, you can check the error types based on the number of flashes emitted by the LED.

1 flash - Battery protection cut-out.

The voltage is outside the cut-out setting.

2 flashes - Fan over-current cut out.

The fan loads the electronic unit with more than one Amp.

3 flashes -Motor start error.

The rotor might be blocked or the differential pressure in the refrigeration system is too high.

4 flashes -Minimum motor speed error.

If the refrigeration system is overloaded, then the motor cannot be maintained a minimum speed at approximately 1850 rpm.

5 flashes -Thermal cut out of the electronic unit.

If the refrigeration system has been too heavily loaded or the ambient temperature is high, the electronic unit will run too hot.

Protection Systems

Danfoss BD35F compressor system has facilities against its overload and starts failure, fan overload, electronic unit loading, and destructive battery discharge. When the overload protection feature is activated, the compressor enters a cycle in which it attempts to start at 66 seconds intervals approximately until a successful start is achieved.

Voltage protection - If a voltage other than the specified range is applied to the electronic unit, then the compressor doesn't start or it stops the exceeded voltage limit during operation. Moreover, your BD compressor will restart after a minute automatically when the supply voltage has reached the reset voltage. If a fan is there, it also starts running automatically without a delay once the reset voltage is reached.

Battery protection - The Danfoss BD electronic unit has integrated battery protection to avoid permanent damage to the battery due to heavy discharge and to ensure sufficient battery power for the correct operation of the compressor.  Moreover, the compressor is stopped and restarted again as per dedicated voltage limits measured on positive and negative terminals of the electronic unit.

Final Words

Danfoss BD compressors bring comfort at work and leisure. So, when you get problems with the Danfoss compressor , repair it quickly. However, we hope this Danfoss BD35F compressor troubleshooting guide helped you to fix the problem. Additionally, you can get more information regarding Danfoss BD compressor troubleshooting, safety precautions, etc. in the owner's manual. Stay connected with us to get more HVAC components troubleshooting tips.

Hobart Rack Oven Troubleshooting & Error Codes

Hobart rack ovens are ideal for baking, roasting, and reheating a variety of food. Rotating rack ovens control the heat so that it will be dispersed evenly throughout the unit. As a result, you can cook everything including bread, pastries, meat, and casseroles thoroughly and evenly. It's no matter how these ovens are efficient, issues will attack in rare conditions so that proper troubleshooting is important. Our Hobart rack oven troubleshooting & error codes blog helps you to fix the issue quickly.

Hobart Rack Oven Troubleshooting & Error Codes

Follow these handy Hobart oven troubleshooting tips to solve commonly encountered problems and error codes.

Burners Not Light ON

Door - The door should not be in the open position. So, check that the loading door is closed properly and the door switch is actuated.

Unfortunately, sometimes, the oven will shut off. See if it is in OFF condition. Turn back ON by pressing the ON button to turn the unit ON.

Ensure that the oven's gas shutoff valve and gas valve are in ON mode.

Reset your Hobart rack oven. To reset it, you have to turn off the unit and wait for five minutes. Now, turn the oven to ON. Allow the oven to cool.

Circulation Fan Runs when Oven is Turned OFF

 If your oven circulation fan is running even it is turned off, you have to check whether your oven is shifted to cooling mode. Close the door properly to cancel the cooling mode. If that door is not opening, contact a service-authorized person.

Steam Time can't Set Properly

If the steamer time is unable to set above 10 seconds and time increments by one second. For this problem, first, you should check if the unit is in food service or pulse stream mode. You need to return your oven to bakery mode. So, check the foodservice mode instructions and change the setting.

Oven Rack Not Lift and Rotate

When the bake time has not been entered in timer or the timer has not been started, the oven's rack is not rotated or lift. So, you have to reenter the time in timer and the press START button. Still, the problem persists, take the repair from authorized service.

Error Codes and Alarm Messages

Temperature display changes between a number and COOL

A cool-down mode is active could be the reason behind this error display. To fix this issue, you need to return it to normal mode by closing the oven door or pressing any button.

Display is flashing with no beep sound while the unit is in a timed bake cycle and is calling for heat

It might cause of temperature recovery alert. To avoid this situation, you have to open and close the oven door to reset the heat control. Still, your rack oven does not begin heating, you should consult the service center.

‘SHdn’ appearing on display

It will happen when your safety alarm has disabled your Hobart rack oven. So, turn off all power supplies and gas to the unit. Then, refer to the owner's manual or take the repair help from a local authorized service professional.

Control beeps continuously

There was the rack rotation alert. You have to check whether the rack is rotating. Also, verify for pans that are protruding from the oven's rack and fix the issue. If you are unable to fix it, call your service professional.

Controls beeps rapidly

It could be a temperature alert for Kosher mode. Check for the vent is activated. If it is, make sure to turn the vent off. Inspect that the gas oven burner is firing. If the burner is not firing, simply open the door and close it to reset the temperature control.

Display shows "LOC OUT"

This problem will appear when your oven is in Kosher Lock Out mode. To change this mode, you need to contact your local service technicians.

How to Clean Hobart Rack Oven?

Regular cleaning is the key to prevent common issues in your unit. Before starting, make sure you disconnect the electrical power to the oven and follow the lockout procedure. Be sure all circuits are disconnected. You take care when operating or cleaning the oven as the Hobart rack oven and parts are hot.

Open the oven door and allow it to cool.

Clean the oven outside daily with a clean and damp cloth.

Remove racks of oven and clean as you would any cooking utensil. You can use warm, soapy water and a brush to clean the utensils. Rinse with water and you have to dry with a cloth.

You should have care while cleaning around sensitive interior parts like probes, sensors, or the rotating mechanism components.

Clean the stainless steel interior of your oven by using a clean cloth and warm soapy water.

Gently scrape the heavy buildup off door glass. When the oven is cool, you can remove the residue with a glass cleaner.

If your unit is equipped with hood filters, clean them with soap and warm water.

Don't use oven cleaners or steel wool on stainless steel surfaces. Moreover, never spray down the oven with steam or water.

Preventive Maintenance

You should keep the oven on a regular preventive maintenance schedule. The oven requires specific maintenance based on the usage and environmental factors. So, follow the maintenance tips to prevent higher repair costs, shortened lifespan, unsafe operating conditions on your Hobart oven.

Inspect the area around the oven that must be clear from combustibles and free. Be sure that there should be no obstructions to the airflow.

Conclusion

That’s all about Hobart oven troubleshooting. Hope this guide useful to make your job easier. You can refer to the manual if you need any special instructions on your unit. Sometimes, you have to replace the Hobart oven parts when they got damaged. Choose 

york parts

York is an international manufacturer of heating, ventilation, and air conditioning (HVAC) products. It manufacturing its products for both residential as well as commercial applications. Its product line will be supplied to various industries such as factories, hospitals, stores, office buildings, shopping malls, airports, residences, marine vessels, etc. The company also designs its equipment, refrigeration, and gas compression for industries like food processing, beverages, and petrochemicals.

York was established in 1874 in York, Pennsylvania by six members. It has a partnership with the other company in 1885 and produced the first ice machine for customers in Mississippi.

York manufactures various products of heating and cooling, indoor air quality, and thermostats. Its product line includes air conditioners, air handlers, evaporator coils, furnaces, heat pumps, mini-split systems, packaging units, energy recovery ventilator, heat recovery ventilator, hybrid electronic air cleaner, media air cleaners, steam humidifiers, ultraviolet air treatment system, whole house bypass humidifiers, whole-house dehumidifiers, steam humidifiers, and fan-powered humidifiers. In addition to this, it supplies HX touch screen thermostats.

York makes home heating and cooling equipment is more efficient and more reliable that will give you more comfort. You can get cleaner and more comfortable air with these indoor air quality equipment.

Getting the right parts for your York equipment is the right decision to keep them in perfect working condition. Looking for York Parts? Don't use any other parts for repair or replacement. Whether you are looking for filters, capacitors, compressors, or any other system, York parts are there. York HVAC parts will make sure the job is done perfectly.

So, access the York parts like York Heater Parts, York Air Conditioner Parts, York Furnace Parts, and more to complete your repair/ replacement work. PartsAPS carries OEM York replacement parts for all commercial and residential units. Hence, choose from our large selection of parts that are designed specifically for your equipment.

Some of our York parts include

a) 23 NG Burner Orifice (.0154) For York Part #S1-9951-1541

b) #32 Burner Orifice For York Part #S1-029-20423-032

c)#40(.098) Gas Orifice For York Part #S1-9951-0981

d)#41 LP Gas Orifice.096” For York Part #S1-9951-0961

e) #44 Gas Orifice For York Part #S1-9951-0861

f) #45 Burner Orifice For York Part #S1-029-21182-245

g) #56 Pilot Orifice (.0456)For York Part #S1-029-20422-056

h) #84 ORIFICE For York Part# S1-029-19387-019

PartsAPS has the full line of York HVAC Parts. So, you can get these OEM parts for the replacement of York air conditioners, heat pumps, air handlers, ventilator units, and furnace models. So, simply find what you need and get it ordered. Our goal is to help our customers succeed in their business.

How To Clean A Hot Dog Roller Grill ?

A commercial hot dog roller is the best choice when you want to heat a large batch of hot dogs or sausages. So, many foodservice centers such as restaurants, convenience stores, and stadiums use these hot dog roller grills. However, you should focus on maintenance to keep your unit in great working order. Also, proper cleaning ensures a clean environment in your establishment. The following tips will instruct you on how to clean a hot dog roller grill.

How to Clean a Hot Dog Roller Grill?

Many people know about how to use a hot dog roller but they don’t aware of its cleaning process. So, here, we have updated some simple steps to clean the hot dog roller grill.

Regular Cleaning:

If you serve a lot of hot dogs, wipe down the machine every few hours to prevent a high amount of food residue as well as fat that is stuck to the rollers. Here are some easy instructions for the daily cleaning of hot dog roller grills.

When the grill is off, turn on rollers and set the temperature to high, and let down rollers to heat until loosening grease and particles stuck to rollers. Otherwise, remove the divider kit to get access to rollers if applicable.

Before you begin, you should use heat resistant gloves to avoid burning hands or fingers while wiping down.

You have to use a soft damp cloth to wipe each roller. Start the wiping from the end of the grill and go towards the middle. You should not wipe into the end of the roller as this will cause to get the grease and particles into the bearings so that they may damage the machine mechanics. Moreover, as abrasive materials damage the coating on the rollers, never use abrasive materials or any powders to wipe down the grills.

Once the grease and particles are removed, wipe the grill full of soapy water using a soft cloth as per the above step. This step is optional when you clean the machine between every use

Cleaning at End of the Day:

Follow these directions to clean and sanitize the unit each day after use.

With the roller off, you have to remove the plug and allow it to cool before starting the cleaning.

Moreover, remove any hot dogs that are remained on the roller.

Check for the machine at its highest temperature setting and ON the rollers. The highest heat setting helps to remove the grease and food particles from the machine,

After five minutes, change the heat setting to "low" or "hold". Now, using a soft cloth dampened with mild soap and hot water or cloth filled with ice wipe down the rollers. You should wipe with cloth from the edge to the center of the roller for avoiding grease and particles from getting to the bearings. Never use oven cleaners or abrasive materials on non-stick roller assemblies.

After completion of wiping down the rollers, soak the cloth in soapy hot water. Again clean the rollers with this cloth with the following of the above step.

Once it is finished, rinse the roller grill with a separate soft cloth.

Separate the drip pan or accessories and clean them thoroughly with hot water and mild soap.

Also, clean the outside of the unit with a soft cloth dampened with mild soap and hot water. You can wipe these stainless steel parts with a cleaner like gold medal watchdog stainless cleaner. You should not use oven cleaners as they will damage hot dog roller parts.

Now, let it down for drying completely, or use a dry cloth to dry completely.

Once the unit dry, you can install the removed drip pan or parts on the roller.

Roller grill cleaning pads and holders also available in the market for cleaning your machine. If you need any hot dog roller repair or replacement, you can take the help of an authorized service technician.

Hot dog roller replacement parts are needed when your machine got damaged or broken. So, identify the required parts when servicing the unit. Moreover, when ordering you have to check the part name, number, and quantity. PartsFPS sells hot dog roller parts so that you can purchase from us. Whatever you need, simply search with part number and get it instantly. Online order is available.

Maintenance Instructions:

The unit should be grounded properly to prevent electrical shocks. Never immerse any part of the hot dog roller in water. Although, do not use excessive water when cleaning. Always unplug the machine before cleaning. Read and follow the owner’s manual instructions thoroughly for installation and operation.

Final Words:-

Hope you got the instructions on how to clean a hot dog roller grill. Still, if you have any doubt, you can check your manufacturer's manual to get detailed instructions. Remember that PartsFPS provides you original hot dog roller parts for replacement needs.

Amana Goodman Parts

Amana Goodman is the member of the Daikin Group which is the world’s largest manufacturer of the HVAC (Heating, Ventilation, and Air Conditioning) products and systems. This company was founded in the year 1975 and is based in Houston, Texas. The major Amana Goodman Parts include the heat pumps, gas furnaces, air handlers and coils, residential split air conditioners, packaged unit and Comfort Net controls, and thermostats. Shop for the best Goodman Air Conditioner Parts, Amana Goodman Furnace Parts, and Goodman HVAC Parts from PartsAPS.

In the year 1982, this company acquired Janitrol and entered the HVAC(Heating, Ventilation, and Air Conditioning) market. It expanded its products offering in 1986 which included the gas heating products.

In the year 2001, Goodman separated the appliances business from the HVAC business to the Maytag Corporation. For the best Goodman Air Conditioner Parts and Amana Goodman Furnace Parts and Pressure Switch For Amana-Goodman Part.

Amana Goodman, from the very beginning, has the same core philosophy, which is to provide its customers with great quality products that can be relied upon, and that will definitely meet their needs by lasting longer. The Goodman manufacturing has a wide range of air conditioning, heat pumps, gas furnaces, and packaged units for taking care of all your heating and cooling requirements.

Moreover, Amana Goodman has a complete range of the high-quality residential and commercial air-conditioning and heating equipment. PartsAPS has a huge collection of the Amana Goodman Parts that include Amana Goodman Furnace Parts, Goodman Air Conditioner Parts, and Goodman HVAC Parts and Amana Goodman Pressure Switches. You can get all your most needed Goodman Replacement Parts on our website at very reasonable prices.

The dedication of Amana Goodman is to develop innovative products which can definitely build to last longer. The Amana Goodman Parts are quite affordable and carries the best warranty. So, if you are looking for the high-quality Amana Goodman Furnace Parts, Goodman Air Conditioner Parts, and Goodman HVAC(Heating, Ventilation, and Air Conditioning) Parts, then this is your ultimate platform. 

Hobart Rack Oven Troubleshooting & Error Codes

Hobart rack ovens are ideal for baking, roasting, and reheating a variety of food. Rotating rack ovens control the heat so that it will be dispersed evenly throughout the unit. As a result, you can cook everything including bread, pastries, meat, and casseroles thoroughly and evenly. It's no matter how these ovens are efficient, issues will attack in rare conditions so that proper troubleshooting is important. Our Hobart rack oven troubleshooting & error codes blog helps you to fix the issue quickly.

Hobart Rack Oven Troubleshooting & Error Codes

Follow these handy Hobart oven troubleshooting tips to solve commonly encountered problems and error codes.

Burners Not Light ON

Door - The door should not be in the open position. So, check that the loading door is closed properly and the door switch is actuated.

Unfortunately, sometimes, the oven will shut off. See if it is in OFF condition. Turn back ON by pressing the ON button to turn the unit ON.

Ensure that the oven's gas shutoff valve and gas valve are in ON mode.

Reset your Hobart rack oven. To reset it, you have to turn off the unit and wait for five minutes. Now, turn the oven to ON. Allow the oven to cool.

Circulation Fan Runs when Oven is Turned OFF

 If your oven circulation fan is running even it is turned off, you have to check whether your oven is shifted to cooling mode. Close the door properly to cancel the cooling mode. If that door is not opening, contact a service-authorized person.

Steam Time can't Set Properly

If the steamer time is unable to set above 10 seconds and time increments by one second. For this problem, first, you should check if the unit is in food service or pulse stream mode. You need to return your oven to bakery mode. So, check the foodservice mode instructions and change the setting.

Oven Rack Not Lift and Rotate

When the bake time has not been entered in timer or the timer has not been started, the oven's rack is not rotated or lift. So, you have to reenter the time in timer and the press START button. Still, the problem persists, take the repair from authorized service.

Error Codes and Alarm Messages

Temperature display changes between a number and COOL

A cool-down mode is active could be the reason behind this error display. To fix this issue, you need to return it to normal mode by closing the oven door or pressing any button.

Display is flashing with no beep sound while the unit is in a timed bake cycle and is calling for heat

It might cause of temperature recovery alert. To avoid this situation, you have to open and close the oven door to reset the heat control. Still, your rack oven does not begin heating, you should consult the service center.

‘SHdn’ appearing on display

It will happen when your safety alarm has disabled your Hobart rack oven. So, turn off all power supplies and gas to the unit. Then, refer to the owner's manual or take the repair help from a local authorized service professional.

Control beeps continuously

There was the rack rotation alert. You have to check whether the rack is rotating. Also, verify for pans that are protruding from the oven's rack and fix the issue. If you are unable to fix it, call your service professional.

Controls beeps rapidly

It could be a temperature alert for Kosher mode. Check for the vent is activated. If it is, make sure to turn the vent off. Inspect that the gas oven burner is firing. If the burner is not firing, simply open the door and close it to reset the temperature control.

Display shows "LOC OUT"

This problem will appear when your oven is in Kosher Lock Out mode. To change this mode, you need to contact your local service technicians.

How to Clean Hobart Rack Oven?

Regular cleaning is the key to prevent common issues in your unit. Before starting, make sure you disconnect the electrical power to the oven and follow the lockout procedure. Be sure all circuits are disconnected. You take care when operating or cleaning the oven as the Hobart rack oven and parts are hot.

Open the oven door and allow it to cool.

Clean the oven outside daily with a clean and damp cloth.

Remove racks of oven and clean as you would any cooking utensil. You can use warm, soapy water and a brush to clean the utensils. Rinse with water and you have to dry with a cloth.

You should have care while cleaning around sensitive interior parts like probes, sensors, or the rotating mechanism components.

Clean the stainless steel interior of your oven by using a clean cloth and warm soapy water.

Gently scrape the heavy buildup off door glass. When the oven is cool, you can remove the residue with a glass cleaner.

If your unit is equipped with hood filters, clean them with soap and warm water.

Don't use oven cleaners or steel wool on stainless steel surfaces. Moreover, never spray down the oven with steam or water.

Preventive Maintenance

You should keep the oven on a regular preventive maintenance schedule. The oven requires specific maintenance based on the usage and environmental factors. So, follow the maintenance tips to prevent higher repair costs, shortened lifespan, unsafe operating conditions on your Hobart oven.

Inspect the area around the oven that must be clear from combustibles and free. Be sure that there should be no obstructions to the airflow.

Conclusion

That’s all about Hobart oven troubleshooting. Hope this guide useful to make your job easier. You can refer to the manual if you need any special instructions on your unit. Sometimes, you have to replace the Hobart oven parts when they got damaged. Choose 

How to Clean a Dirty Flame Sensor on a Furnace

 A flame sensor is one of the most essential components in the furnace. The flame sensor acts as a safety device that shuts off the gas to the burners if flame is not detected. If this flame sensor is dirty, it doesn't sense the flame and shut the gas off. A dirty flame sensor is the most common issue that you encounter with the furnace system. Also, it might be caused your furnace to lock out or continue trying to sense the flame. If your furnace fires up and stops within seconds,, then consider that you have a flame sensing problem. Hence, know how to clean furnace flame sensor and keep your sensor clean to work perfectly.

How to Clean Furnace Flame Sensor?

A furnace flame sensor is a thin metallic rod, located on the burner assembly. Normally, the sensor bents and sits just in front of the pilot flame inside the furnace system. When the thermostat indicates that the furnace to turn on, the gas valve opens up and fires gas into the combustion chamber where the ignitor or pilot lights the burners.

The sensor will be there to confirm that there is fire present when the gas valve is open. If there is no sensor present, the pilot light can go out and dangerous gas might be leaked. So, a flame sensor is a safety measure for your furnace. If this sensor doesn't identify the flame when the gas is open, it shuts down everything to keep you safe. In the latest furnace models, the shutdown process can be done up to three times before lockout.

Causes of a Dirty Flame Sensor on Furnace

The flame sensor will become dirty just because of carbon build-up. Moreover, this sensor is sensitive to variations in the readings that it takes. Even a thin coating of carbon also causes the sensor to read improperly and then shut down. Although, most furnaces are located in basements and attics so tends to be a lot of dust in the air. Over time, the dust or dirt on the furnace burns up and cause to carbon buildup on it's flame sensor.

How to Clean Flame Sensor?

Following are the required tools to clean the flame sensor on your furnace.

1/4 inch hex driver or wrench. This may vary depending on the type of mounting screw.

Emery cloth, steel wool or light grit sandpaper.

Dry and clean paper towel.

Shut off Power to the Furnace

Whenever you start the maintenance, you should turn off the power to your furnace. Shut off the thermostat won't turn off power to the unit. So, you have to shut off the power manually. You can have a toggle switch, i.e., an on/ off switch on or near the furnace. If you don't have this toggle switch, you need to shut off the power to the furnace at the circuit breaker box.

If your furnace doesn't have an electronically controlled gas valve, turn the gas off to the furnace also. It is just for safety, don't worry about gas leaks.

As there are many different models of furnaces, these points may not match with you. Then, you should not proceed without shutdown the furnace. Call an HVAC technician to fix the furnace.

Take Out the Furnace Flame Sensor

Once the furnace didn't get power, you have to locate and remove the flame sensor from the unit. The flame sensor is easily accessible and it can be found mounted with a hex head screw. You have to remove that screw carefully.

After removing the screw, simply slide out the sensor for cleaning. This sensor is a sensitive component so you should take care while removing it. Also, you have a chance that you need to disassemble a wire located at the sensor end to work freely.

Clean the Flame Sensor

It's time to clean the flame sensor of your furnace. Gently rub the rod with light grit sandpaper or scrubbing brush to remove carbon buildup. Make sure you won't rub anything other than the rod.

Here, you are not doing heavy sanding so just give enough force for removing that carbon buildup. After sanding, wipe away the dust that gets left behind from the sanding with a paper towel.You should not use any chemicals as they leave residue or damage the flame sensor.

Replace the Sensor

The flame sensor doesn't need to spark like new. Just removing carbon buildup is enough before replacing it. Before remounting the sensor on the burner assembly, you should reconnect the wire if it has any. Use the hex head screw to remount. If you lost that screw, you can buy a new screw from a hardware store. Mount the sensor securely and close the furnace door. Next, shut on power to the unit.Now, turn the gas and electricity back on, fire up the furnace to check it’s working.

Wrap Up

After completion of flame sensor cleaning, your furnace needs to run normally by setting a degree high temperature. Now, your unit will kick on, reach the temperature and shut off as normally it would. If you feel difficult to know how to clean a dirty flame sensor on a furnace, just call an HVAC professional to fix it.

How to Program a Pitco Fryer?

This blog explains how to program a Pitco fryer by providing details on the operation and adjustment of the cooking computer control developed for Pitco fryer products. This microprocessor offers the latest cooking technology including cook temperature adjustment, drain valve interlock, faulty probe detection, beeper volume, selectable melt cycles, etc. Each product key may be programmed with the cook, shake and hold times to keep place with changing menus over time.

How to Program a Pitco Fryer?

Check out the programming instructions for your Pitco fryer.

To Turn the Fryer ON

When you have been given the power to the appliance, it displays [OFF]. Press the [I/O] key. Then, it displays will show one of the normal: [Heating]; [Melting] [Solid]/ [Liquid]; or [Ready]. You can see some messages in both left and right displays. However, you have to wait until the appliance heats up to the [Ready] condition before cooking.

To Turn OFF the Appliance

You have to tap on the [I/O] button. Now, it displays a software version number and then [OFF] [OFF]. You will need to use the left [I/O] key for the left side and the right [I/O] key for the right of dual vat control.

To Start Cook

When the display is showing [Ready], the fryer has reached set temperature and is ready to cook. Tap on the required product key and then place it onto the vat. If the cook timer is running, the indicator which is above the product key will flash.

To Cancel Cook

You should press and hold the product key to cancel a cook cycle. If no other cooks are pending, the digital controller displays as [Ready].

To check Actual and Set Temperatures

To know the actual vat temperature, you have to tap on the thermometer key. Then, you can see [ACT nnnF] or [ACT nnnC] on the display, "nnn" is the current temperature. After a few seconds, the display shows [READY], [MELT] or [HEATING] when no cooks are running or, [CKn mm:ss] for any cooks still running.

To see the set temperature, press the thermometer key two times. Now, the display will shows [SET nnnF] or [SET nnnC], where nnn is the current temperature reading. Then after a few moments, it will return to [READY], [MELT ], or [HEATING]. If there is any cook still running, it shows [CKn mm:ss].

To check Current Settings for Cook, Shake, and Hold Times

To view the current settings for shake, cook, and hold times, you should press the clock key, followed by the desired product key. It displays [CKn mm:ss], followed by [SHn mm:ss], then [HDn mm:ss], where "n" indicates key number and "mm:ss" are the current settings for time. After that, the display returns to [READY], [MELT] or [HEATING] or, [CKn mm:ss].

To Enter Programming Level 1With no cook timers running, display will show one of the following: [HEATING], [MELT] [LIQUID (or SOLID)], or [READY].

You need to press the [p] key. Then, the left display will show [PROGRAM] and the right one will be blank. Now, enter the password by using the product keys.

To set cook temperature:

You have to press on the thermometer button once for a single vat or press twice for a dual vat. Now, you can see [SET xxxF] [TEMP] or [SET xxxC] [TEMP], where "xxx" is the temperature setting. By using the product keys, you can enter the numerics to adjust the present setting. After that, press the [P] key to save the setting. Now, it shows [PROGRAM]. If you want to exist, you will need to press [P] again or continue.

To change cook, shake, and hold times:

Cook time

Cook time may be set for each product key. If you want to deactivate it for any product, enter zero value to that particular. Press on [Clock] Key, it will display [Select] [Product]. Now, you have to press the desired product key to change. When it shows [nCK mm:ss] [TIME], you should enter the numbers to adjust the current setting. To save the changes, click on the [Clock] button and continue setup for this product key.

Shake time

Shake time is an alarm that sounds during cook time to prompt you to shake the basket. It has a default value of zero that means the shake time is inactive. To use this, you should set a value less than cook time. Display shows [nSH mm:ss] [TIME] where “n” is the key number, “SH” means shake, and “mm:ss” is time in minutes and seconds.

Hold time

In your fryer, cooked item will stand in holding bins for a period of time. This timer produces an alarm to inform you to remove the old item and start a new cook cycle. By default it is inactive. Display shows [nHD mm:ss] [TIME], where “n” is the key number, “HD means HOLD, and “mm:ss” is minutes and seconds. Enter the time and save the current setting by pressing the [Clock] key.

To Enter Programming Level 2

The display must shows [Program]. When the [0] key is pressed, it displays [Select] [Options]. Indicator lights above the product key will illuminate to represent options that may be changed.

Fahrenheit or Celsius display

The Controller will display temperatures in the Fahrenheit or Celsius scales. The default scale is °F. When display showing [PROGRAM], you will need to press the product key [0]. Then, you can see [SELECT] [OPTIONS]. You have to tap product key 1, it displays [DEGREE n] [F OR C], where “n” is the current setting. To scroll through choices (F or C), you have to use [0]. Press [P] to save the changes.

Password change

With factory default settings, you will not require to enter programming levels 1 and 2. The password might be activated or changed in this position. You have to press the product key 2, with display showing [PROGRAM], press the product key [0] display will show [SELECT] [OPTIONS]. When you press key 2, it shows [SET PASS] [NEW PASS]. Use the product key [0] to scroll through choices [NO PASS] or [PASS REQ] and tap on the [P] key to save choice. You have to choose one of these choices and proceed accordingly.

Conclusion

Hope this information provided above helped you to manage your Pitco fryer. If you need more instructions on how to program a Pitco fryer, you can check the owner’s manual. Stay in touch with us to get more guides on other kitchen equipment programming.

How To Clean A Scotsman Ice Machine

Most ice machines require periodic maintenance to maintain their performance at optimum capability. According to the instructions of the Scotsman ice machine cleaning manual, you must keep the maintenance to guarantee longevity. If you are looking for a complete resource on how to clean a Scotsman ice machine, continue reading this post. Our guide will help you to find the solutions for Scotsman ice machine cleaning.

How to Clean a Scotsman Ice Machine?

Initially, you have to remove all ice from the ice bin.

After that, remove the front panel of your ice maker.

Now, push and release the Harvest button to run the Harvest cycle.

You have to wait until the machine's Harvest cycle is completed and stop.

Once the cycle has been completed, you need to remove the evaporator cover.

Run the clean cycle. To run the clean cycle, push and release the clean button. When the cycle has started, you can see that the clean button indicator light blinking and the pump will restart.

Pour 12 ounces of Scotsman ice machine cleaner into the reservoir water. Next, return the evaporator cover to its normal position.

You have to wait for 10 minutes while the cleaning solution in the ice maker circulates.

Again, you need to push and release the clean button to start the rinse process. If the rinsing process has started, you can confirm with the indicator light ON. This rinsing process flushes any residual cleaner out of the ice maker's water system.

Wait about twenty minutes for completing the rinsing process and to remove any residual cleaning solution.

Turn off the switch of the Scotsman ice machine.

Now, you need to sanitize the ice maker.

Take and mix the two gallons of ice machine sanitizer solution.

Now press the clean button for starting the sanitization.

You need to pour 18 ounces of sanitizer solution into the reservoir water.

Prepare Scotsman Ice Machine Cleaning Solutions

Here, you can know how to prepare Scotsman ice machine cleaning solutions.

Descaling Solution

The descaling state should be performed with a scale remover. This is the acid so you should handle with care. Make sure you use the descaler solution according to the instructions given to remove scale from where it can build up on your ice machine including a water reservoir, evaporator assembly, drop zone, water distribution tubes and ice bin. We recommend you use a nickel-safe ice machine scale remover.

Use a quat-based cleaner for the disinfecting and sanitizing stages. However, we recommend a simple mixture of water and bleach as a descaler remover. The dilution rates may be varied depending on which product you have chosen.

Disinfection Solution

This disinfection solution comprised of higher amounts of bleach. It is safe because this disinfection solution is be required to be rinsed away. Mix 6 ounces of bleach with a gallon of water to make the disinfection solution.

Sanitization Solution

A more diluted Sanitization solution will be left on the machine to air dry, hence it contains a lower level of bleach. Mix 2 teaspoons of bleach with one gallon of water for making sanitizer. However, locally, you may have different sanitization ratio requirements so you should follow them.

Additional Components Cleaning

For best performance, you should perform other parts cleaning also as part of your routine maintenance.

Air filters: Pull the air filters from the machine's front panel. Check and wash out any grease or dust on the air filter with water. After drying, you need to re-install them.

Air-cooled condenser: If your machine is not working well with the air filters cleaning, then, you will need to clean the air-cooled condenser fins. You can find these fins under the evaporator fan blades.

Exterior surfaces: You must clean all exterior surfaces with a high-quality stainless steel cleaner. Wipe down the top & side panels and wipe down the front for removing dust, grease and fingerprints

Water filters: If your Scotsman ice machine is connected to water filters, there is a need of cartridges replacement if they have been installed for more than 6 months.

Manitowoc ice machine cleaner

Conclusion

However, regular maintenance is an important thing to keep your ice machine running well. Hope, our suggestions on how to clean a Scotsman ice machine helped you to remove dust, dirt and grease simply. If you need any further assistance related to Scotsman ice machine cleaning, you can check your owner’s manual. For Scotsman ice machine replacement parts, choose PartsFPS store.